Differences

This shows you the differences between two versions of the page.

--- asennusohjeet:kylkikisko [2026/06/26 15:41] – Korjattu etusivu-linkit valman
+++ asennusohjeet:kylkikisko [2026/06/26 18:21] (current) – [Sako M92S] 86.115.63.116
@@ Line 1: / Line 1: @@
-====== Kylkikisko ja tähtäinjalka – Asennusohje ======
+====== AK2.0-kylkikisko ja AK2.0-tähtäinjalka – Asennusohje ======
 Kylkikisko on tähtäinjärjestelmän perusta. Sen asennus vaatii äärimmäistä huolellisuutta.
+**Asennusvideo:** [[https://www.youtube.com/watch?v=6HZ3hqT9U8k|Katso asennusvideo YouTubessa]]
 Tuotenumerot: [[yhteensopivuus|katso yhteensopivuustaulukko]]
-===== Suomeksi – Jyrsittyrunkoinen ja peltirunkoinen AK =====
+===== Jyrsittyrunkoinen ja peltirunkoinen AK =====
 Yleistä: jos asennus tuntuu epävarmalta, anna asesepän hoitaa asennus.
@@ Line 31: / Line 33: @@
   - Kiinnitä tähtäimenjalka, tähtäin ja radalle.
-===== Suomeksi – Sako M92 =====
+===== Sako M92S / RK95 =====
 Yleistä: jos asennus tuntuu epävarmalta, anna asesepän hoitaa asennus.
@@ Line 47: / Line 49: @@
 ----
-===== In English – AK2.0 Sight Rail Installation (V1.0) =====
-  - Fieldstrip your AK (remove receiver cover, recoil spring, bolt carrier, bolt), leave hammer cocked
-  - Remove the selector by lifting it from the AK's receiver and rotating clockwise until it points directly upwards. Now you can lift the selector from your rifle
-  - Put the drilling jig to your AK's left side so that the alignment screw goes to the selector hole
-  - Keep the drilling jig in place firmly and drill two 8.5mm holes through the receiver. Use good quality drill bits
-  - Remove burrs from the holes with a file or a deburring hook. Remove all debris from inside the receiver.
-  - Check that the receiver rail fits nicely. If it doesn't, check if some burrs or filings are between the rail and receiver
-  - Put some medium thread locker between the receiver rail and the receiver. Put some thread locker to the screws.
-  - Screw the bolts in place. You need TRX30 and 10mm wrench. Make them tight.
-  - Attach the selector in reverse order
-  - Attach the sight rail. Tighten the bolts with a screwdriver or 10mm wrench. **Note!** These don't need to be enormously tight – the special washers prevent the nuts from loosening
-  - Assemble the rifle
-  - Attach your optic of choice
-  - Sight in your optic and rock'n'roll
-  - Periodically check that all screws are tight
-Please also check our AK2.0 YouTube channel: [[https://www.youtube.com/channel/UC6hr8zpGZm7ixcAKr4Nmkig|AK2.0 YouTube]]
-Installation video: [[https://www.youtube.com/watch?v=6HZ3hqT9U8k|Installation video]]
-----
 ===== Valmet Petra: kylkikiskon asennusvaihtoehdot — VA301011 =====